Clear Glazing Protection Film

Clear Glazing Protection Film

Product Details

Benefits:

  • 24/7 Safety & Security: film holds shattered glass together to protect against the hazards of broken glass falling from a window.
  • Cost Savings: in the event of an impact, film is less expensive to replace than safety glass.
  • Clear Appearance: provides invisible safety and security.
  • Extensively Tested
  • Professionally Installed

In addition, Clear safety and security film blocks unwanted ultraviolet ray exposure without changing the appearance of glass. Clear safety and security film is available in an exterior application when required.

Anchoring Systems for Spontaneous Breakage

Madico always recommends the use of an anchoring restraint system for glass with spontaneous breakage. There are many anchoring restraint systems available. Mechanical anchoring such as FrameGard®, which holds the film in place through a combination of screws and tape and an aluminum extrusion. This is by far the safest attachment system, tested to hold from 500 to 800 pounds per linear foot of attachment.

Because many frames and building situations do not allow for screws to be used, the Wet Glaze attachment system is the most common attachment method used for these applications. Wet glaze attachment systems have been thoroughly tested to blast mitigation standards and wind loads. As such, Wet glaze attachment systems are a very practical choice for NiS failure mitigation.

In a Wet Glaze installation, the safety film is installed in a daylight configuration, after which a sizeable bead of structural silicone is installed with a minimum of a 1/2-inch (13 mm) contact with the film and the frame. Heavier pieces of glass may require a bead which uses 3/4-inch (19 mm) or larger contact on both the film and frame system.

Choosing the best system for your glass is based on the weight of the glass and the type of framing system. Contact your Madico sales representative and Madico Technical Services for aid in calculating the bead size.

Nickel sulfide (NiS) inclusions are small, pencil point size particles or imperfections that may be found within a sheet of glass. These are not an issue in common annealed glass but when tempered/toughened glass they can expand due to thermal cycles, breaking the outer plane of compression, causing the entire sheet of glass to explode. 

Although tempered/toughened glass breaks into small light pieces, these pieces may still cause injury to people should they fall out of a building above pedestrians. Through our testing, Madico has seen that portions of many panes of tempered/toughened glass, once broken, will hold together until they impact the ground. This allows large portions of glass to strike with considerable weight and force. 

Buildings with spontaneous breaks have used safety films for years to hold a broken sheet of tempered glass in place once NiS failure occurs. Depending on the size and weight of the glass, a 7 or 8 mil safety films is used to hold the glass together. For exterior applications, an exterior grade 7 mil safety film is used. 

Due to the break pattern of tempered glass, Madico does not recommend a simple daylight installation of safety film. Daylight installations is when the film is installed on the visible part of the glass. In this type of installation, once spontaneous breakage occurs, the entire sheet of filmed glass may potentially fall from the opening. The small pieces of broken glass encapsulated within the frame are insufficient to hold the filmed glass within the frame.

Madico always recommends the use of an anchoring restraint system for glass with spontaneous breakage. There are many anchoring restraint systems available. Mechanical anchoring such as FrameGard®, which holds the film in place through a combination of screws and tape and an aluminum extrusion. This is by far the safest attachment system, tested to hold from 500 to 800 pounds per linear foot of attachment. 

Because many frames and building situations do not allow for screws to be used, the Wet Glaze attachment system is the most common attachment method used for these applications. Wet glaze attachment systems have been thoroughly tested to blast mitigation standards and wind loads. As such, Wet glaze attachment systems are a very practical choice for NiS failure mitigation. 

In a Wet Glaze installation, the safety film is installed in a daylight configuration, after which a sizeable bead of structural silicone is installed with a minimum of a 1/2-inch (13 mm) contact with the film and the frame. Heavier pieces of glass may require a bead which uses 3/4-inch (19 mm) or larger contact on both the film and frame system. 

Choosing the best system for your glass is based on the weight of the glass and the type of framing system. Contact your Madico sales representative and Madico Technical Services for aid in calculating the bead size.

Safety Glazing Materials Used in Buildings

The Consumer Product Safety Commission (CPSC) and ANSI standards establish the specifications and methods of test for the safety properties of safety glazing materials (glazing materials designed to promote safety and reduce the likelihood of cutting and piercing injuries when the glazing materials are broken by human contact) as used for all building and architectural purposes.

Madico safety and security films have been extensively tested by independent testing facilities and meet safety glazing criteria as defined by CPSC, the U.S. Consumer Product Safety Commission and Underwriters Laboratories.

Includes a Manufacturer’s Warranty in North America. Ask your dealer for details.

Benefits

Stands up to Mother Nature

Our safety & security films are engineered so glass is shatter-resistant against high-powered winds and storms, preventing water and wind-borne debris from entering.

Reduce Hazards from Explosions

Broken glass is one of the main causes of death or injury during an explosion. Madico window security films reduce these hazards by keeping shattered glass together.

Leave Criminals Empty Handed

By holding shattered glass together, our window security laminate films deter and slow smash-and-grabbers because they can’t get in quickly, as well as looters from illegally entering.

Manufactured by Madico

When you purchase Madico film you can rest assured that you have selected a high quality and extensively tested product.

Headquartered in Tampa Bay, Florida, Madico, Inc. manufactures and distributes high performance window films for automotive, architectural, and safety and security applications through seven company owned distribution centers in the United States as well as an extensive international distributor network.

Madico films are installed by highly trained professional dealers who are experts in selecting the best product for each customer’s unique need and application.

 

Learn More from IWFA

Learn More from the International Window Film Association.

 

 

 



Professional Resources


These and other resources for architects and engineers can also be downloaded from ARCAT.

Professional Resources


CL 700 PS SR 3 Part Spec

Click to download

CL 800 PS SF 3 Part Spec

Click to download

CL 700 Design Guide

Click to download

CL 700 Exterior Design Guide

Click to download

CL 800 Design Guide

Click to download


Please fill out the form to access the product's data sheet